Description
SealGreen Concrete Patch Repair is a cementitious stainable material design for grouting small hairline cracks, divots created from the removal of wood carpet strips, and small holes in interior concrete floors.
SealGreen Concrete Patch can be stain, painted or seal. SealGreen Concrete Patch is design for hairline crack repair from 1/32-inches to ¼-inch wide cracks. Do not use this product for resurfacing. Must be installed at temperatures over 50ºF.
Mixing and Application:
Mix small quantities by hand using 3 parts by volume of powder to 1 part of water. Use a margin trowel and mix vigorously for 2-3 minutes. Mix thoroughly to obtain a lump-free consistency. The pot life of SealGreen Concrete Patch is approximately 20 minutes at 70ºF. If the product begins to set in the bucket, remix before using. Do not add more water. Additional water will weaken the dressing and lower its strength. In warm weather, use cold water to extend the working time.
Recommended Tools
Mixing buckets, margin trowel, steel trowel, sponges. For small cracks, it is recommended to apply with sponge using tile grouting practices,
Curing
Requires no special curing procedures, avoid applying this product if rain is expected within 6-8 hours or freezing temperatures could occur within 24 hours of application. As with any cementitious material, the above conditions can alter the appearance and performance of the dressing.
Notes
Mix Ratio: 3 parts powder to 1 part by volume of water at 70ºF
Walkable: Light Foot traffic in 2 hours. Vehicular traffic in 6-8 hours
Storage: Store in a cool dry area. Do not expose to sun.
Shelf Life: One year
TECHNICAL PRODUCT DESCRIPTION
SealGreen Concrete Patch Repair is a is a cementitious stainable material design for grouting small hairline cracks, divots created from the removal of wood carpet strips, and small holes in interior concrete floors. SealGreen Concrete Patch Repair is ONLY a cementitious filler and it is NOT designed to repair concrete or acquire bonding strength.Concrete Patch Repair is a pre-blended, sanded product. The standard formulation meets ASTM C 270 and C 1714 for Type N mortar.
COLORS: SealGreen Concrete Patch Repair is only available in gray
SIZES: 1Qrt Bottle
APPLICABLE STANDARDS
ASTM International
• ASTM C 270 Specification for Mortar for Unit Masonry
• ASTM C 387 Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
• ASTM C 1714 Specification for Preblended Dry Concrete Patch Repair for Unit Masonry
PHYSICAL/CHEMICAL PROPERTIES
SealGreen Concrete Patch Repair meets or exceeds the property requirements of ASTM C 270, ASTM C 387 and ASTM C 1714 for the type selected. Refer to Appendix XI of ASTM C270 for guidance in selecting the proper mortar type. See Table 1.
INSTALLATION
SURFACE PREPARATION: Surfaces to receive Concrete Patch Repair should be clean and free of dirt, loose debris, grease, oil, etc., for the best possible bond.
MIXING
Mix small quantities by hand using 3 parts by volume of powder to 1 part of water. Use a margin trowel and mix vigorously for 2-3 minutes. Mix thoroughly to obtain a lump-free consistency. The pot life of SealGreen Concrete Patch is approximately 20 minutes at 70ºF. If the product begins to set in the bucket, remix before using. Do not add more water. Additional water will weaken the dressing and lower its strength. In warm weather, use cold water to extend the working time.
INSTALLATION
• Apply using a similar method to grouting ceramic tile. Push downward into the concrete crack with a yellow grouting sponge. Use same process for divots or small hole in concrete. Level the mortar with the concrete surface and let dry.
• Using a sponge sand block, remove all excess material until patch is even with the concrete surface.
