Poly Step Guard

From: $108.00

Poly Step Guard is a water-based, concrete and masonry sealer that dries clear. Poly Step Guard is a 1-part solution with no VOCs that requires no mixing. Poly Step Guard with Anti-skid bonds effectively with various flooring surfaces, and won’t etch or damage your floor’s natural appearance.

Description

This product is custom made and large orders may take up to two weeks to ship. It also ships FREE but only by UPS ground shipping. No rush shipping!

Poly Step Guard is a water-based, concrete and masonry sealer that dries clear. Poly Step Guard is a 1-part solution with no VOCs that requires no mixing. Poly Step Guard with Anti-skid bonds effectively with various flooring surfaces, and won’t etch or damage your floor’s natural appearance.

Poly Step Guard acts a waterproof sealer. It protects surfaces and grout lines from stains and discoloration caused by liquids, cleaning products and other contaminates. It has built-in UV protection that shields surfaces from fading, as well as mildewcides to prevent the growth of mold and mildew.

Poly Step Guard with Anti-skid prevents slip and fall accidents in areas that are likely to become extremely wet or slippery. It offers a relatively smooth texture, and provides slip resistance with the use of very small aggregate particles and nanotechnology materials; similar in texture to 400-grit sandpaper.

Poly Step Guard is designed for indoor surfaces that need anti slip protection, but must maintain a close appearance to the original surface. It is a favorable solution for polished stone surfaces such as marble and granite found in homes and lobbies; as well as wood- or vinyl-laminate flooring in homes and office environments. This eco-friendly product contains extremely low VOC’s, and has no fumes or odors. It can be applied easily with a paint brush, paint roller or low pressure airless spray.

Application Tips:

  • Apply Poly Step Guard between 50° – 70° fahrenheit
  • It’s best to apply in the mornings when the concrete is cool, before the substrate heats up from the sun.
  • DO NOT apply on windy days. This will make the sealer cure too quickly which can lead to “clouding” or white spots in the sealer.
  • “Thin to win!” It’s better to apply multiple thin layers using a short nap roller instead of one thick layer (when it’s warmer out or a little windy).
  • Work out of a paint tray instead of pouring directly onto the concrete.
  • Back roll the sealer immediately to ensure no areas are missed.

Benefits – Poly Step Guard

    • Green: Non-Toxic, Minimal VOC’s, Fumes, Odors
    • Multi-Surface Solution
    • Ease of Application
    • Single Component Product (No Mixing Req’d)
    • Highly Water Resistant
    • Does Not Mold or Mildew
    • Protects Grout Lines
    • Quick Drying Times
    • Enhanced for UV Protection (Does not yellow, crack or peel)
    • Does Not Harm Underlying Floor Surface
    • Does Not Attract Dirt
    • Stain Resistant
    • Easy To Clean

Poly Step Guard may be used in homes and commercial applications, to increase safety and to prevent slip and fall injuries. Its durability outlasts competitors, and reduces the need for expensive floor care and maintenance. This eco-friendly product contains extremely low VOC’s, and has no fumes or odors. It can be applied easily with a paint brush, paint roller or low pressure airless spray.

Application Directions:

Poly Step Guard may be applied by brush, roller (short nap) or low pressure airless spray. A gallon of Poly Step Guard can provide protection over approximately 350 to 400 square feet depending on the nature of the surface. Stir or shake the Poly Step Guard container vigorously to mix well prior to use. The targeted surface should be free of dirt, debris and oil or grease, prior to application. Highly recommended to clean floor with SealGreen Oil Cleaner Degreaser. The coating goes on easily and dries to a clear glossy finish.

One coat is usually sufficient. However if a second is coat is desired, allow the first coat to dry thoroughly for an hour or more depending on ambient temperature. Allow 24 hours or more for full cure before subjecting the surface to heavy traffic. Do not apply at temperatures below 5°F or above 90°F. Avoid heavy buildup, puddling and overlapping. See Product Specifications sheet. High Humidity will impact curing time. Do not apply on very humid environments. Poly Step  Guard applies the same as the SealGreen E10 epoxy sealer, and SealGreen E15 Stamped Concrete Sealer, and SealGreen W10 Finish Coat. The video demonstrates how easy is to applied the product.

Clean Up:

Appropriately mask off areas that need to be kept free of Poly Step Guard. Wipe off overruns, spills and splatters immediately with water. Thoroughly clean hands and tools after use with soap and warm water. Observe all personal precautions as you would with any other paint or coating product.

Additional information

Weight 9 lbs
Dimensions N/A
Size

1 qt., 1 gal., 4 gal.